The Sound Enthusiast’s Companion: High-Quality Recording Tips

10 Recording Tips for Recording Audio with High Quality

Richard Bennett

Oct 26, 2023• Proven solutions

0

Getting the best sound for your recording is not as simplistic as buying an expensive microphone. There are many different things you can do to record your audio more clearly. Here are 10 recording tips to record high-quality audio.

1. Silence everything you don’t want your microphone to record
2. Put your mobile phone in airplane mode
3. Minimize echo
4. Block wind from reaching your microphone
5. Upgrade your microphone
6. Adjust your levels
7. Start with a sound cue if you’re planning to do some syncing in post
8. Get close to the sound
9. ADR
10. Record Ambient Sound

Bonus Tip-Record Your Audio with Wondershare Filmora

Wondershare Filmora has great recording features that enable you to record screen , voiceover, and webcam. Just connect the recording device to your computer, and start the recording in Wondershare Filmora and you will get high-quality audio. And you can also easily pick a song from the royalty-free music library on Wondershare Filmora. These audio features on Filmora are rare and very simple to use, you only need to click a few times and your video will have a new sound and background song.

1. Silence everything you don’t want your microphone to record

When you’re recording audio, you have to be more aware of the subtle sounds that drone on in your background. These sounds may include humming from machines with fans, buzzing from lights, and jingling from your pet’s collar. Observe your recording space and find ways to silence everything that you don’t want in your audio recording.

2. Put your mobile phone in airplane mode

Although it may be quite obvious to turn your phone’s ring tone off when you’re recording, it may not be as obvious to put your phone in airplane mode. When phones receive calls or perform searches as part of their background processes, they emit signals that can get picked up by your recording system. Avoid ruining good takes with unwanted sounds of phone signals by putting your phones in airplane mode.

3. Minimize echo

If you are recording yourself talk or sing, make sure to set up your recording space in a way where the sound projected from your voice bounces minimally off the walls and back to your microphone. Bare walls and hardwood floors will cause a lot of bouncing. Make use of materials that will absorb your sound rather than bounce it, like a thick rug or a comforter. If you want your voice to echo, that’s something you should do in post-production.

4. Block wind from reaching your microphone

Although it might not sound so loud and distracting to the naked ear, wind sounds terribly loud through a microphone recording and can cause your audio to clip (distortion of waveform due to output of sound exceeding maximum capacity or 0 dB point). This includes the “wind” that comes out of your mouth when you pronounce words starting with the letter “p.” Use pop filters, windscreens, and deadcats to block wind from reaching your microphone.

5. Upgrade your microphone

As much as you try to control all the noise in your surroundings, your greatest recording limitation will come from the hardware that you use. Improve your recordings by plugging in an external microphone into your camera’s microphone jack or record audio completely separately with a professional microphone.

Need help with deciding on a microphone to buy? Check out our recommended list of microphones.

6. Adjust your levels

Before pressing the record button, see how loudly your microphone picks up the sound you wish to record. Adjust your levels (sensitivity of your microphone) until the sound sits in between -6 dBs and -12dBs. This range gives the source of your sound some room to get louder without the recorded audio getting clipped. When you first listen to audio recorded within this range, it may sound very quiet. No need to worry though because you can increase the volume later in editing.

7. Start with a sound cue if you’re planning to do some syncing in post

If you’re recording separate audio that you plan to sync to your video later in editing, start your recording with a short and loud sound cue like a clap or a high pitched “beep” tone. Later, when you’re editing, it’ll be much easier for you to find the section where your video and additional audio match.

8. Get close to the sound

Unless you’re aiming to record ambient sound, bring your microphone close to the source of sound you are wanting to record. The closer your microphone is to the source of sound, the lower your sensitivity setting can be on your microphone. As a result of lowering your levels, sounds you are not meaning to record will also sound fainter.

9. ADR

When you need to record a scene in a loud setting where you have very little control over the noise, record additional vocals later and replace the original vocals through a process called automated dialogue replacement.

10. Record Ambient Sound

Remember to record ambient sound or “room tone.” You can use these recordings to fill in the blanks if you run out of audio and also smooth out parts of your audio where you hear pops, clicks, and other unwanted noise.

Richard Bennett

Richard Bennett is a writer and a lover of all things video.

Follow @Richard Bennett

Richard Bennett

Oct 26, 2023• Proven solutions

0

Getting the best sound for your recording is not as simplistic as buying an expensive microphone. There are many different things you can do to record your audio more clearly. Here are 10 recording tips to record high-quality audio.

1. Silence everything you don’t want your microphone to record
2. Put your mobile phone in airplane mode
3. Minimize echo
4. Block wind from reaching your microphone
5. Upgrade your microphone
6. Adjust your levels
7. Start with a sound cue if you’re planning to do some syncing in post
8. Get close to the sound
9. ADR
10. Record Ambient Sound

Bonus Tip-Record Your Audio with Wondershare Filmora

Wondershare Filmora has great recording features that enable you to record screen , voiceover, and webcam. Just connect the recording device to your computer, and start the recording in Wondershare Filmora and you will get high-quality audio. And you can also easily pick a song from the royalty-free music library on Wondershare Filmora. These audio features on Filmora are rare and very simple to use, you only need to click a few times and your video will have a new sound and background song.

1. Silence everything you don’t want your microphone to record

When you’re recording audio, you have to be more aware of the subtle sounds that drone on in your background. These sounds may include humming from machines with fans, buzzing from lights, and jingling from your pet’s collar. Observe your recording space and find ways to silence everything that you don’t want in your audio recording.

2. Put your mobile phone in airplane mode

Although it may be quite obvious to turn your phone’s ring tone off when you’re recording, it may not be as obvious to put your phone in airplane mode. When phones receive calls or perform searches as part of their background processes, they emit signals that can get picked up by your recording system. Avoid ruining good takes with unwanted sounds of phone signals by putting your phones in airplane mode.

3. Minimize echo

If you are recording yourself talk or sing, make sure to set up your recording space in a way where the sound projected from your voice bounces minimally off the walls and back to your microphone. Bare walls and hardwood floors will cause a lot of bouncing. Make use of materials that will absorb your sound rather than bounce it, like a thick rug or a comforter. If you want your voice to echo, that’s something you should do in post-production.

4. Block wind from reaching your microphone

Although it might not sound so loud and distracting to the naked ear, wind sounds terribly loud through a microphone recording and can cause your audio to clip (distortion of waveform due to output of sound exceeding maximum capacity or 0 dB point). This includes the “wind” that comes out of your mouth when you pronounce words starting with the letter “p.” Use pop filters, windscreens, and deadcats to block wind from reaching your microphone.

5. Upgrade your microphone

As much as you try to control all the noise in your surroundings, your greatest recording limitation will come from the hardware that you use. Improve your recordings by plugging in an external microphone into your camera’s microphone jack or record audio completely separately with a professional microphone.

Need help with deciding on a microphone to buy? Check out our recommended list of microphones.

6. Adjust your levels

Before pressing the record button, see how loudly your microphone picks up the sound you wish to record. Adjust your levels (sensitivity of your microphone) until the sound sits in between -6 dBs and -12dBs. This range gives the source of your sound some room to get louder without the recorded audio getting clipped. When you first listen to audio recorded within this range, it may sound very quiet. No need to worry though because you can increase the volume later in editing.

7. Start with a sound cue if you’re planning to do some syncing in post

If you’re recording separate audio that you plan to sync to your video later in editing, start your recording with a short and loud sound cue like a clap or a high pitched “beep” tone. Later, when you’re editing, it’ll be much easier for you to find the section where your video and additional audio match.

8. Get close to the sound

Unless you’re aiming to record ambient sound, bring your microphone close to the source of sound you are wanting to record. The closer your microphone is to the source of sound, the lower your sensitivity setting can be on your microphone. As a result of lowering your levels, sounds you are not meaning to record will also sound fainter.

9. ADR

When you need to record a scene in a loud setting where you have very little control over the noise, record additional vocals later and replace the original vocals through a process called automated dialogue replacement.

10. Record Ambient Sound

Remember to record ambient sound or “room tone.” You can use these recordings to fill in the blanks if you run out of audio and also smooth out parts of your audio where you hear pops, clicks, and other unwanted noise.

Richard Bennett

Richard Bennett is a writer and a lover of all things video.

Follow @Richard Bennett

Richard Bennett

Oct 26, 2023• Proven solutions

0

Getting the best sound for your recording is not as simplistic as buying an expensive microphone. There are many different things you can do to record your audio more clearly. Here are 10 recording tips to record high-quality audio.

1. Silence everything you don’t want your microphone to record
2. Put your mobile phone in airplane mode
3. Minimize echo
4. Block wind from reaching your microphone
5. Upgrade your microphone
6. Adjust your levels
7. Start with a sound cue if you’re planning to do some syncing in post
8. Get close to the sound
9. ADR
10. Record Ambient Sound

Bonus Tip-Record Your Audio with Wondershare Filmora

Wondershare Filmora has great recording features that enable you to record screen , voiceover, and webcam. Just connect the recording device to your computer, and start the recording in Wondershare Filmora and you will get high-quality audio. And you can also easily pick a song from the royalty-free music library on Wondershare Filmora. These audio features on Filmora are rare and very simple to use, you only need to click a few times and your video will have a new sound and background song.

1. Silence everything you don’t want your microphone to record

When you’re recording audio, you have to be more aware of the subtle sounds that drone on in your background. These sounds may include humming from machines with fans, buzzing from lights, and jingling from your pet’s collar. Observe your recording space and find ways to silence everything that you don’t want in your audio recording.

2. Put your mobile phone in airplane mode

Although it may be quite obvious to turn your phone’s ring tone off when you’re recording, it may not be as obvious to put your phone in airplane mode. When phones receive calls or perform searches as part of their background processes, they emit signals that can get picked up by your recording system. Avoid ruining good takes with unwanted sounds of phone signals by putting your phones in airplane mode.

3. Minimize echo

If you are recording yourself talk or sing, make sure to set up your recording space in a way where the sound projected from your voice bounces minimally off the walls and back to your microphone. Bare walls and hardwood floors will cause a lot of bouncing. Make use of materials that will absorb your sound rather than bounce it, like a thick rug or a comforter. If you want your voice to echo, that’s something you should do in post-production.

4. Block wind from reaching your microphone

Although it might not sound so loud and distracting to the naked ear, wind sounds terribly loud through a microphone recording and can cause your audio to clip (distortion of waveform due to output of sound exceeding maximum capacity or 0 dB point). This includes the “wind” that comes out of your mouth when you pronounce words starting with the letter “p.” Use pop filters, windscreens, and deadcats to block wind from reaching your microphone.

5. Upgrade your microphone

As much as you try to control all the noise in your surroundings, your greatest recording limitation will come from the hardware that you use. Improve your recordings by plugging in an external microphone into your camera’s microphone jack or record audio completely separately with a professional microphone.

Need help with deciding on a microphone to buy? Check out our recommended list of microphones.

6. Adjust your levels

Before pressing the record button, see how loudly your microphone picks up the sound you wish to record. Adjust your levels (sensitivity of your microphone) until the sound sits in between -6 dBs and -12dBs. This range gives the source of your sound some room to get louder without the recorded audio getting clipped. When you first listen to audio recorded within this range, it may sound very quiet. No need to worry though because you can increase the volume later in editing.

7. Start with a sound cue if you’re planning to do some syncing in post

If you’re recording separate audio that you plan to sync to your video later in editing, start your recording with a short and loud sound cue like a clap or a high pitched “beep” tone. Later, when you’re editing, it’ll be much easier for you to find the section where your video and additional audio match.

8. Get close to the sound

Unless you’re aiming to record ambient sound, bring your microphone close to the source of sound you are wanting to record. The closer your microphone is to the source of sound, the lower your sensitivity setting can be on your microphone. As a result of lowering your levels, sounds you are not meaning to record will also sound fainter.

9. ADR

When you need to record a scene in a loud setting where you have very little control over the noise, record additional vocals later and replace the original vocals through a process called automated dialogue replacement.

10. Record Ambient Sound

Remember to record ambient sound or “room tone.” You can use these recordings to fill in the blanks if you run out of audio and also smooth out parts of your audio where you hear pops, clicks, and other unwanted noise.

Richard Bennett

Richard Bennett is a writer and a lover of all things video.

Follow @Richard Bennett

Richard Bennett

Oct 26, 2023• Proven solutions

0

Getting the best sound for your recording is not as simplistic as buying an expensive microphone. There are many different things you can do to record your audio more clearly. Here are 10 recording tips to record high-quality audio.

1. Silence everything you don’t want your microphone to record
2. Put your mobile phone in airplane mode
3. Minimize echo
4. Block wind from reaching your microphone
5. Upgrade your microphone
6. Adjust your levels
7. Start with a sound cue if you’re planning to do some syncing in post
8. Get close to the sound
9. ADR
10. Record Ambient Sound

Bonus Tip-Record Your Audio with Wondershare Filmora

Wondershare Filmora has great recording features that enable you to record screen , voiceover, and webcam. Just connect the recording device to your computer, and start the recording in Wondershare Filmora and you will get high-quality audio. And you can also easily pick a song from the royalty-free music library on Wondershare Filmora. These audio features on Filmora are rare and very simple to use, you only need to click a few times and your video will have a new sound and background song.

1. Silence everything you don’t want your microphone to record

When you’re recording audio, you have to be more aware of the subtle sounds that drone on in your background. These sounds may include humming from machines with fans, buzzing from lights, and jingling from your pet’s collar. Observe your recording space and find ways to silence everything that you don’t want in your audio recording.

2. Put your mobile phone in airplane mode

Although it may be quite obvious to turn your phone’s ring tone off when you’re recording, it may not be as obvious to put your phone in airplane mode. When phones receive calls or perform searches as part of their background processes, they emit signals that can get picked up by your recording system. Avoid ruining good takes with unwanted sounds of phone signals by putting your phones in airplane mode.

3. Minimize echo

If you are recording yourself talk or sing, make sure to set up your recording space in a way where the sound projected from your voice bounces minimally off the walls and back to your microphone. Bare walls and hardwood floors will cause a lot of bouncing. Make use of materials that will absorb your sound rather than bounce it, like a thick rug or a comforter. If you want your voice to echo, that’s something you should do in post-production.

4. Block wind from reaching your microphone

Although it might not sound so loud and distracting to the naked ear, wind sounds terribly loud through a microphone recording and can cause your audio to clip (distortion of waveform due to output of sound exceeding maximum capacity or 0 dB point). This includes the “wind” that comes out of your mouth when you pronounce words starting with the letter “p.” Use pop filters, windscreens, and deadcats to block wind from reaching your microphone.

5. Upgrade your microphone

As much as you try to control all the noise in your surroundings, your greatest recording limitation will come from the hardware that you use. Improve your recordings by plugging in an external microphone into your camera’s microphone jack or record audio completely separately with a professional microphone.

Need help with deciding on a microphone to buy? Check out our recommended list of microphones.

6. Adjust your levels

Before pressing the record button, see how loudly your microphone picks up the sound you wish to record. Adjust your levels (sensitivity of your microphone) until the sound sits in between -6 dBs and -12dBs. This range gives the source of your sound some room to get louder without the recorded audio getting clipped. When you first listen to audio recorded within this range, it may sound very quiet. No need to worry though because you can increase the volume later in editing.

7. Start with a sound cue if you’re planning to do some syncing in post

If you’re recording separate audio that you plan to sync to your video later in editing, start your recording with a short and loud sound cue like a clap or a high pitched “beep” tone. Later, when you’re editing, it’ll be much easier for you to find the section where your video and additional audio match.

8. Get close to the sound

Unless you’re aiming to record ambient sound, bring your microphone close to the source of sound you are wanting to record. The closer your microphone is to the source of sound, the lower your sensitivity setting can be on your microphone. As a result of lowering your levels, sounds you are not meaning to record will also sound fainter.

9. ADR

When you need to record a scene in a loud setting where you have very little control over the noise, record additional vocals later and replace the original vocals through a process called automated dialogue replacement.

10. Record Ambient Sound

Remember to record ambient sound or “room tone.” You can use these recordings to fill in the blanks if you run out of audio and also smooth out parts of your audio where you hear pops, clicks, and other unwanted noise.

Richard Bennett

Richard Bennett is a writer and a lover of all things video.

Follow @Richard Bennett

How to Craft Eye-Catching YouTubes End Titles

How to Create YouTube Intros & End Cards - Free and Easy

Shanoon Cox

Oct 26, 2023• Proven solutions

0

Part 1: Intros

Elements of an Intro

Top Intro Sites

Creating an Intro in Filmora

Part 2: End Cards

Elements of an End Card

How To Make an End Card

Part1: Intros

Elements of an Intro

Intros should only last about five seconds, and that can be cut down to two or three if you have a larger following.

When your intro video is longer than five seconds viewers are more likely to click away. The first 15 seconds of a video is when viewers are most likely to decide to click on one of the recommended videos, or go back to their search results and choose something else. The odds of them leaving within these first 15 seconds are greater if you do not get right to the main point of your video. That is why long intro sequences are bad for your watch time.

Whether it is better to put your intro at the very beginning of your video, or after you introduce your topic, will depend on your viewers. You may want to try it both ways and then look at your retention report (found in your YouTube Creator Studio under Analytics) to see which works best for you.

Top Intro Sites

There are a few different sites where you can download animated intros, customized to include your username or logo. Here are two of the best:

FlixPress.com

This is probably the most popular intro site. There are a lot of great animated intros available for under $5, or even for free.

IntroMaker.net

This is another site with really professional looking intros for $5. They only have two free options, though.

Creating an Intro in Filmora

You can create a simple intro card in Filmora.

1. Choose your background. You may want to use a short clip as your intro, or you may just want a colored background.
2. Drag your clip or background into the video track of your timeline and trim it down to five seconds.
3. If you have a logo, import it into Filmora and drag it into your picture-in-picture track.
4. With your logo selected, click on the Green Screen icon. In the pop-up, select the background of your logo to make it transparent. For this to work your logo cannot be the same color as its background.
5. Click on the editing icon with your logo selected and choose an animation.
6. Go to the Text/Titles menu and choose an animated title that suits your channel. Drag it into your text track and edit it to include your name.
7. The last piece of your intro is sound. You can choose a song from Filmora’s library and cut it down to five seconds, or import your sound effect.
8. Export your video and save it for use in all of your other videos.

Part 2: End Cards

When your video ends, YouTube will recommend a selection of videos users may want to watch next. Often, these recommendations will not include more of your videos.

To keep viewers on your channel, you can create your End Card which recommends other content you have created.

Elements of an End Card

An end card includes clips from two or three of your videos, muted, and shrunk down to thumbnail-size. Using spotlight annotations you can make these thumbnails click-able.

It is also important that your end card includes multiple calls to action. A call to action is meant to spur a viewer to some kind of action. Writing ‘Check out this video’ above one of your thumbnails is a call to action.

You should also have a subscribe link somewhere in your end card, ideally a very noticeable button with a proven call to action like ‘Subscribe Now!’.

Some creators will leave their end cards at that and play music overtop, but it can be even more effective to include a voiceover where you ask viewers to subscribe and watch your other videos.

How To Make an End Card

1. Choose a static background. You may want to download an end card template or create one in a drawing program. If you do, make sure to include calls to action like ‘Watch more!’ and ‘Subscribe’.
2. Drag your background into your timeline at the end of your video.
3. Import two or three of your previous videos and drag them into your picture in picture tracks. Each clip should be on its track.
4. Trim the clips in your picture in picture track down to the same length as your end card.
5. Shrink your clips down to thumbnail-size by dragging their corners in the preview window.
6. Position your clips so they are spaced evenly by dragging them in the preview screen.
7. Mute your clips.
8. If your background does not include any calls to action, choose a title from the Text/Titles menu in Filmora and create at least two – one asking viewers to subscribe, and one asking them to watch your suggested videos.
9. Export your video from Filmora and upload it to YouTube.
10. Go to your Video Manager and select Annotations in the drop-down menu next to your video.
11. Go to your end card in the previewer, as that is where you want to add your annotations.
12. Click Add Annotation and add a spotlight annotation to your video. Stretch it over one of your thumbnails and then check the Link box under your Annotation’s timing. Insert a link to the video you are previewing.
13. Repeat for any other thumbnails. For your subscribe button, change where it said ‘Video’ to ‘Subscribe’ and enter your channel URL.
14. Click Apply Changes.

Shanoon Cox

Shanoon Cox is a writer and a lover of all things video.

Follow @Shanoon Cox

Shanoon Cox

Oct 26, 2023• Proven solutions

0

Part 1: Intros

Elements of an Intro

Top Intro Sites

Creating an Intro in Filmora

Part 2: End Cards

Elements of an End Card

How To Make an End Card

Part1: Intros

Elements of an Intro

Intros should only last about five seconds, and that can be cut down to two or three if you have a larger following.

When your intro video is longer than five seconds viewers are more likely to click away. The first 15 seconds of a video is when viewers are most likely to decide to click on one of the recommended videos, or go back to their search results and choose something else. The odds of them leaving within these first 15 seconds are greater if you do not get right to the main point of your video. That is why long intro sequences are bad for your watch time.

Whether it is better to put your intro at the very beginning of your video, or after you introduce your topic, will depend on your viewers. You may want to try it both ways and then look at your retention report (found in your YouTube Creator Studio under Analytics) to see which works best for you.

Top Intro Sites

There are a few different sites where you can download animated intros, customized to include your username or logo. Here are two of the best:

FlixPress.com

This is probably the most popular intro site. There are a lot of great animated intros available for under $5, or even for free.

IntroMaker.net

This is another site with really professional looking intros for $5. They only have two free options, though.

Creating an Intro in Filmora

You can create a simple intro card in Filmora.

1. Choose your background. You may want to use a short clip as your intro, or you may just want a colored background.
2. Drag your clip or background into the video track of your timeline and trim it down to five seconds.
3. If you have a logo, import it into Filmora and drag it into your picture-in-picture track.
4. With your logo selected, click on the Green Screen icon. In the pop-up, select the background of your logo to make it transparent. For this to work your logo cannot be the same color as its background.
5. Click on the editing icon with your logo selected and choose an animation.
6. Go to the Text/Titles menu and choose an animated title that suits your channel. Drag it into your text track and edit it to include your name.
7. The last piece of your intro is sound. You can choose a song from Filmora’s library and cut it down to five seconds, or import your sound effect.
8. Export your video and save it for use in all of your other videos.

Part 2: End Cards

When your video ends, YouTube will recommend a selection of videos users may want to watch next. Often, these recommendations will not include more of your videos.

To keep viewers on your channel, you can create your End Card which recommends other content you have created.

Elements of an End Card

An end card includes clips from two or three of your videos, muted, and shrunk down to thumbnail-size. Using spotlight annotations you can make these thumbnails click-able.

It is also important that your end card includes multiple calls to action. A call to action is meant to spur a viewer to some kind of action. Writing ‘Check out this video’ above one of your thumbnails is a call to action.

You should also have a subscribe link somewhere in your end card, ideally a very noticeable button with a proven call to action like ‘Subscribe Now!’.

Some creators will leave their end cards at that and play music overtop, but it can be even more effective to include a voiceover where you ask viewers to subscribe and watch your other videos.

How To Make an End Card

1. Choose a static background. You may want to download an end card template or create one in a drawing program. If you do, make sure to include calls to action like ‘Watch more!’ and ‘Subscribe’.
2. Drag your background into your timeline at the end of your video.
3. Import two or three of your previous videos and drag them into your picture in picture tracks. Each clip should be on its track.
4. Trim the clips in your picture in picture track down to the same length as your end card.
5. Shrink your clips down to thumbnail-size by dragging their corners in the preview window.
6. Position your clips so they are spaced evenly by dragging them in the preview screen.
7. Mute your clips.
8. If your background does not include any calls to action, choose a title from the Text/Titles menu in Filmora and create at least two – one asking viewers to subscribe, and one asking them to watch your suggested videos.
9. Export your video from Filmora and upload it to YouTube.
10. Go to your Video Manager and select Annotations in the drop-down menu next to your video.
11. Go to your end card in the previewer, as that is where you want to add your annotations.
12. Click Add Annotation and add a spotlight annotation to your video. Stretch it over one of your thumbnails and then check the Link box under your Annotation’s timing. Insert a link to the video you are previewing.
13. Repeat for any other thumbnails. For your subscribe button, change where it said ‘Video’ to ‘Subscribe’ and enter your channel URL.
14. Click Apply Changes.

Shanoon Cox

Shanoon Cox is a writer and a lover of all things video.

Follow @Shanoon Cox

Shanoon Cox

Oct 26, 2023• Proven solutions

0

Part 1: Intros

Elements of an Intro

Top Intro Sites

Creating an Intro in Filmora

Part 2: End Cards

Elements of an End Card

How To Make an End Card

Part1: Intros

Elements of an Intro

Intros should only last about five seconds, and that can be cut down to two or three if you have a larger following.

When your intro video is longer than five seconds viewers are more likely to click away. The first 15 seconds of a video is when viewers are most likely to decide to click on one of the recommended videos, or go back to their search results and choose something else. The odds of them leaving within these first 15 seconds are greater if you do not get right to the main point of your video. That is why long intro sequences are bad for your watch time.

Whether it is better to put your intro at the very beginning of your video, or after you introduce your topic, will depend on your viewers. You may want to try it both ways and then look at your retention report (found in your YouTube Creator Studio under Analytics) to see which works best for you.

Top Intro Sites

There are a few different sites where you can download animated intros, customized to include your username or logo. Here are two of the best:

FlixPress.com

This is probably the most popular intro site. There are a lot of great animated intros available for under $5, or even for free.

IntroMaker.net

This is another site with really professional looking intros for $5. They only have two free options, though.

Creating an Intro in Filmora

You can create a simple intro card in Filmora.

1. Choose your background. You may want to use a short clip as your intro, or you may just want a colored background.
2. Drag your clip or background into the video track of your timeline and trim it down to five seconds.
3. If you have a logo, import it into Filmora and drag it into your picture-in-picture track.
4. With your logo selected, click on the Green Screen icon. In the pop-up, select the background of your logo to make it transparent. For this to work your logo cannot be the same color as its background.
5. Click on the editing icon with your logo selected and choose an animation.
6. Go to the Text/Titles menu and choose an animated title that suits your channel. Drag it into your text track and edit it to include your name.
7. The last piece of your intro is sound. You can choose a song from Filmora’s library and cut it down to five seconds, or import your sound effect.
8. Export your video and save it for use in all of your other videos.

Part 2: End Cards

When your video ends, YouTube will recommend a selection of videos users may want to watch next. Often, these recommendations will not include more of your videos.

To keep viewers on your channel, you can create your End Card which recommends other content you have created.

Elements of an End Card

An end card includes clips from two or three of your videos, muted, and shrunk down to thumbnail-size. Using spotlight annotations you can make these thumbnails click-able.

It is also important that your end card includes multiple calls to action. A call to action is meant to spur a viewer to some kind of action. Writing ‘Check out this video’ above one of your thumbnails is a call to action.

You should also have a subscribe link somewhere in your end card, ideally a very noticeable button with a proven call to action like ‘Subscribe Now!’.

Some creators will leave their end cards at that and play music overtop, but it can be even more effective to include a voiceover where you ask viewers to subscribe and watch your other videos.

How To Make an End Card

1. Choose a static background. You may want to download an end card template or create one in a drawing program. If you do, make sure to include calls to action like ‘Watch more!’ and ‘Subscribe’.
2. Drag your background into your timeline at the end of your video.
3. Import two or three of your previous videos and drag them into your picture in picture tracks. Each clip should be on its track.
4. Trim the clips in your picture in picture track down to the same length as your end card.
5. Shrink your clips down to thumbnail-size by dragging their corners in the preview window.
6. Position your clips so they are spaced evenly by dragging them in the preview screen.
7. Mute your clips.
8. If your background does not include any calls to action, choose a title from the Text/Titles menu in Filmora and create at least two – one asking viewers to subscribe, and one asking them to watch your suggested videos.
9. Export your video from Filmora and upload it to YouTube.
10. Go to your Video Manager and select Annotations in the drop-down menu next to your video.
11. Go to your end card in the previewer, as that is where you want to add your annotations.
12. Click Add Annotation and add a spotlight annotation to your video. Stretch it over one of your thumbnails and then check the Link box under your Annotation’s timing. Insert a link to the video you are previewing.
13. Repeat for any other thumbnails. For your subscribe button, change where it said ‘Video’ to ‘Subscribe’ and enter your channel URL.
14. Click Apply Changes.

Shanoon Cox

Shanoon Cox is a writer and a lover of all things video.

Follow @Shanoon Cox

Shanoon Cox

Oct 26, 2023• Proven solutions

0

Part 1: Intros

Elements of an Intro

Top Intro Sites

Creating an Intro in Filmora

Part 2: End Cards

Elements of an End Card

How To Make an End Card

Part1: Intros

Elements of an Intro

Intros should only last about five seconds, and that can be cut down to two or three if you have a larger following.

When your intro video is longer than five seconds viewers are more likely to click away. The first 15 seconds of a video is when viewers are most likely to decide to click on one of the recommended videos, or go back to their search results and choose something else. The odds of them leaving within these first 15 seconds are greater if you do not get right to the main point of your video. That is why long intro sequences are bad for your watch time.

Whether it is better to put your intro at the very beginning of your video, or after you introduce your topic, will depend on your viewers. You may want to try it both ways and then look at your retention report (found in your YouTube Creator Studio under Analytics) to see which works best for you.

Top Intro Sites

There are a few different sites where you can download animated intros, customized to include your username or logo. Here are two of the best:

FlixPress.com

This is probably the most popular intro site. There are a lot of great animated intros available for under $5, or even for free.

IntroMaker.net

This is another site with really professional looking intros for $5. They only have two free options, though.

Creating an Intro in Filmora

You can create a simple intro card in Filmora.

1. Choose your background. You may want to use a short clip as your intro, or you may just want a colored background.
2. Drag your clip or background into the video track of your timeline and trim it down to five seconds.
3. If you have a logo, import it into Filmora and drag it into your picture-in-picture track.
4. With your logo selected, click on the Green Screen icon. In the pop-up, select the background of your logo to make it transparent. For this to work your logo cannot be the same color as its background.
5. Click on the editing icon with your logo selected and choose an animation.
6. Go to the Text/Titles menu and choose an animated title that suits your channel. Drag it into your text track and edit it to include your name.
7. The last piece of your intro is sound. You can choose a song from Filmora’s library and cut it down to five seconds, or import your sound effect.
8. Export your video and save it for use in all of your other videos.

Part 2: End Cards

When your video ends, YouTube will recommend a selection of videos users may want to watch next. Often, these recommendations will not include more of your videos.

To keep viewers on your channel, you can create your End Card which recommends other content you have created.

Elements of an End Card

An end card includes clips from two or three of your videos, muted, and shrunk down to thumbnail-size. Using spotlight annotations you can make these thumbnails click-able.

It is also important that your end card includes multiple calls to action. A call to action is meant to spur a viewer to some kind of action. Writing ‘Check out this video’ above one of your thumbnails is a call to action.

You should also have a subscribe link somewhere in your end card, ideally a very noticeable button with a proven call to action like ‘Subscribe Now!’.

Some creators will leave their end cards at that and play music overtop, but it can be even more effective to include a voiceover where you ask viewers to subscribe and watch your other videos.

How To Make an End Card

1. Choose a static background. You may want to download an end card template or create one in a drawing program. If you do, make sure to include calls to action like ‘Watch more!’ and ‘Subscribe’.
2. Drag your background into your timeline at the end of your video.
3. Import two or three of your previous videos and drag them into your picture in picture tracks. Each clip should be on its track.
4. Trim the clips in your picture in picture track down to the same length as your end card.
5. Shrink your clips down to thumbnail-size by dragging their corners in the preview window.
6. Position your clips so they are spaced evenly by dragging them in the preview screen.
7. Mute your clips.
8. If your background does not include any calls to action, choose a title from the Text/Titles menu in Filmora and create at least two – one asking viewers to subscribe, and one asking them to watch your suggested videos.
9. Export your video from Filmora and upload it to YouTube.
10. Go to your Video Manager and select Annotations in the drop-down menu next to your video.
11. Go to your end card in the previewer, as that is where you want to add your annotations.
12. Click Add Annotation and add a spotlight annotation to your video. Stretch it over one of your thumbnails and then check the Link box under your Annotation’s timing. Insert a link to the video you are previewing.
13. Repeat for any other thumbnails. For your subscribe button, change where it said ‘Video’ to ‘Subscribe’ and enter your channel URL.
14. Click Apply Changes.

Shanoon Cox

Shanoon Cox is a writer and a lover of all things video.

Follow @Shanoon Cox

Also read: